R3D GoPod 8
De-Shelled Action Camera Case
YOUR ITEMS ARE PRE-ASSEMBLED TO ORDER FOR YOUR CONVENIENCE, PLEASE ALLOW 5-7 DAYS PRIOR TO SHIPMENT CONFIRMATION.
The R3D GoPod 8 is a flight ready, protective case for your de-shelled action camera needs.
Designed for Hero 8, It features a fully adjustable camera lens tilt of 0°-60° and an integrated soft mounting system.
The GoPod 8 is compatible with supported BEC's, offering easy access to the buttons and JST, SD Card slot and monitor port. Compatible with Mavic 2 Zoom ND filters.
Includes:
(1) GoPod 8 hard shell
(1) GoPod 8 lens mount
(1) 20x20 / 30x30 OR 25x25(whoop) mounting plate
*Hardware is included
Optional purchase:
(1) NameLess RC BEC Hero 8
*De-shelled action camera electronics are NOT included
*ND filter is NOT included
Accessories and spares
NameLessRC BEC
Sold out
For GoPro Hero 8
YOUR ITEMS ARE PRE-ASSEMBLED TO ORDER FOR YOUR CONVENIENCE, PLEASE ALLOW 5-7 DAYS PRIOR TO SHIPMENT CONFIRMATION.
Features:
- The NLRC BEC is specially designed for Naked GoPro HERO 8 which weighs about 2.4g, makes your naked GoPro lighter and easier to install on your drone.
- Comes with the pluggable connector, which is easier to connect with your flight controller for power supply and recording.
- Supports 2-6S power in.
- Automatic power-on function.
- Output voltage is 5V@3A, helps avoid accidental power off which is caused by insufficient power supply.
- Both support LED and BUZZER port. Available pad for pilots to control the GoPro recording via the radio transmitter.
- Bypassed the Pinio remap and FC doesn't need to remap.
- Integrated GoPro stock buttons, Power/Mode Button and Record Button
- Integrated GoPro stock LED to know the status of the camera.
Specification
- Weight: 2.4g
- Output: 5V@2.1A
- Input Voltage: 2-6S
- Connector: PH 1.0 3P Connector
R3D GoPod 6/7
De-Shelled Action Camera Case
YOUR ITEMS ARE PRE-ASSEMBLED TO ORDER FOR YOUR CONVENIENCE, PLEASE ALLOW 5-7 DAYS PRIOR TO SHIPMENT CONFIRMATION.
The R3D GoPod 6/7 is a flight ready, protective case for your de-shelled action camera needs.
Designed for Hero 6/7 it features a fully adjustable camera lens tilt of 0°-60° and an integrated soft mounting system.
The GoPod 6/7 is compatible with supported BEC's, offering easy access to the buttons and JST, SD Card slot, monitor port, and HDMI port. Compatible with Mavic 2 Zoom ND filters.
Includes:
(1) GoPod 6/7 hard shell
(1) GoPod 6/7 lens mount
(1) 20x20 / 30x30 OR 25x25(whoop) mounting plate
*Hardware is included
Optional purchase:
(1) BetaFPV BEC Hero 6/7
*De-shelled action camera electronics are NOT included
*ND filter is NOT included
0 - 60 in a split second
the r3d gopod 8 supports a fully adjustable lens angle from 0°-60° and beyond.
The Lens and hinging point were carefully placed to ensure low stress to the ribbon cable. The ribbon cable is held down in place to ensure no ejects during angle adjustment or FLIGHT. |
|
|
|
How low can you go?
If you follow r3d shifters' design you'd know we do not believe in flying towers.
Our low profile frames have a lower center of gravity that is maintained with our low profile GoPod 8. Better flight, smaller crafts, smaller gaps. |
Like a glove
The r3d Gopod 8 offers a full protective enclosure to your precious electronics while OFFERING full ACCESS SD CARD SLOT and MONITOR PORT.
THE GOPOD 8 IS COMPATIBLE WITH SUPPORTED BEC'S, OFFERING EASY ACCESS TO THE BUTTONS AND JST connectors. The Gopod 8 is also natively COMPATIBLE WITH MAVIC 2 ZOOM ND FILTERS. |
|
|
|
Not just r3d
The R3d GoPod 8 was conceived to compliment our low profile drone frame designs, from ZeroGrav to ION to Isotope.
Though natively mounts to R3D Shifters' fuselages, the GoPod 8 will also mount on any low-profile drone build. your choice between a 25x25 (whoop) or 20x20 / 30x30 mounting plate. |
so how much does it weigh?
GoPod 8 full Kit with mount
|
GOPod 8 build with BEC
|
GoPod 8 build with bec and ND filter
|